推薦新聞
玻璃幕墻使用的丁基防水嵌縫膠
玻璃幕墻就對硅烷改性聚氨酯密封膠提出更高...
硅烷改性聚氨酯密封膠黏度測定方法
裝配式建筑外墻接縫用改性丁基防水嵌縫膠
硅烷改性聚氨酯密封膠黏度測定方法
- 發布時間 : 2024-10-24 15:18:49
- Views:
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
硅烷改性聚氨酯密封膠黏度測定方法
(Summary description)Customized SILICONE STRUCTURAL SEALANT from China manufacturer refers to the adhesive with high strength, can bear large load, aging resistance, fatigue resistance and corrosion resistance, and has stable performance within the expected life. It is suitable for bearing the bonding of strong structural parts. Non structural adhesive has low strength and poor durability. It can only be used for bonding, sealing and fixing of ordinary and temporary properties, and cannot be used for structural adhesive bonding. NEUTRAL SILICONE WETHERPROOF SEALANT from China manufacturer is a structural adhesive with waterproof function. Silicone glue refers to the adhesive based on silicone rubber. According to different functions, it can be divided into structural adhesive, potting adhesive, sealant, thermal conductive adhesive, flame retardant adhesive and so on.
- 發布時間 : 2024-10-24 15:18:49
- Views:
50℃后取出硅烷改性聚氨酯密封膠的配制通過熱處理完成。本實驗以不同質量的填料碳酸鈣作為變量,以質量分?jǐn)?shù)2%,2.5%,3%的填料碳酸鈣制備得到的硅烷改性聚氨酯密封膠作為測試對象,分別記為樣品A、樣品B和樣品。以茹度、硬度、拉伸性能等對膠體加固性能影響作為特性參照條件分別進行對比實驗。
將待測試樣裝人燒杯,按GB/T 2794-2013規定完成茹度測定。將試樣溫度控制在23一25℃,將旋轉茹度計豎直插人試樣中央,但不接觸試樣的底部和試樣的表面,直到試樣的液體標記與試樣的液體表面齊平為止。在標準試驗條件下,向量具筒內注滿密封劑,直到溢出為止,將多余的部分抹去,讓膠體剛好填滿量具筒內的預定容積。將固定體積的硅烷改性聚氨酯密封膠從量具筒中緩慢擠出,置于兩張紙張或者薄膜之間,在紙張或薄膜上壓蓋測稠度專用玻璃板,并在其上面壓放2 kg重的秤陀,開始測量時間;2 min后立即取下秤陀,考察不同填充材料的固化度的影響。將試件掀開直至發現有部分沒有凝固的封口劑粘附在模口上為止,計算材料茹度k:(1)式中:群表示膠體固化層厚度(mm)。為硅烷改性聚氨酯密封膠的固化程度(%);L為墻體裂縫最大深度(mm)。
在墻體裂痕處中填上密封劑,在常溫環境下進行為期7d的養護后把框架刮掉。在標準的環境中,經過7d的養護,將采集的實驗樣本置于電子式萬能材料試驗機,為確保測試精度,在測試過程中采用在壓力工具上涂潤滑油的方法,使用邵氏硬度計在膠條邊緣測定力一變形,以此減小測試誤差。針對裝配式混凝土墻面節點的局部抗剪性能叮、抗剪承載力m及節點剪力傳遞機效率B進行分析,在進行墻體縫隙填補的過程中,隨著正應力Y的增大,接縫局部的承載力也會變得越來越大,導致硅烷改性聚氨酯密封膠在完成縫隙填補后逐漸出現脆性破壞。因此在高幅荷載的作用下,為保證硅烷改性聚氨酯密封膠的接縫效果,需要保障膠體填補后的硬度,計算材料硬度(Tl):Tl= B(0.81 m+0.930(2)。http://www.caffertyclinic.com/
Scan the QR code to read on your phone